StoneFil is filled with 50% of powdered stone. This high stone-filling has resulted in a 3D printer filament with remarkable aesthetic features. StoneFil is an easy-to-print 3D printer filament and printed objects have an extremely matte stone-like finish. Due to its high content of stone powder, its density is higher than regular PLA’s.

StoneFil is a filament which is based on our modified and easy-to-print EasyFil PLA compound.

Unique features

  • Easy to print
  • 50% gravimetric powdered stone filling
  • ±37% heavier than “normal” PLA
  • Matte and rough stone-like finish

 

General printing guidelines *

Nozzle size: ≥ 0.4mm Layer height: ≥ 0.2mm Flow rate: ± 110%
Print temp: ± 215 – 230° C Print speed: Slow Retraction: Yes ± 5mm
Heat bed: ± 0 – 60° C Fan speed: 50-100% Experience level: Beginner

*) Above displayed settings are meant as guidance to find your optimal print settings. These ranges in settings should work for most printers, but please do feel free to experiment outside these ranges if you think it is suitable for your printer. There are a lot of different type of printers, hot-ends and printer offsets that it is extremely difficult to give an overall one-size-fits-all setting.

 

Abrasiveness

StoneFil has a very high filling with stone powders and therefore the filament can have a slightly more abrasive effect on brass nozzles than unfilled filaments.

Filament length

ρ: 1.70 g/cc 50 gr coil 0.5 Kg spool
Ø 1.75mm ± 12.2m ± 122m
Ø 2.85mm ± 4.6m ± 46m

 

Nozzle cleaning

When printing with filled/composite filaments it is recommended to clean your nozzle immediately after printing by feeding 15-20cm PLA filament through your nozzle. This will make sure that any potential fillers are flown out of your nozzle. It is even better to use glow in the dark PLA as the extremely hard phosphorous particles are much more likely to scrape out residual waste from your nozzle.

Product export information

HS Code: 39169090 Description: Monofilament Country of origin: the Netherlands

 

Compliance *

This filament is compliant to below listed directives and regulations.

  • RoHS directive 2011/65/EC
  • REACH directive 1907/2006/EC

*) This declaration of conformity to directives and regulations is prepared according to our present standard of knowledge and may be amended if new cognitions are available and applies only for the above described products.

Technical Datasheet:

Safety Datasheet:

StoneFil

StoneFil is a PLA-based 3D printer filament with a 50% powdered stone filling, which give 3D printed parts true stone-like aesthetics and a rough and matt stone-like surface finish.

1.75
2.85
Concrete
Granite
Pottery Clay
Terracotta
250
500
2000
SKU: StoneFil Tags: , , , , ,

StoneFil

StoneFil is a PLA-based 3D printer filament with a 50% powdered stone filling, which give 3D printed parts true stone-like aesthetics and a rough and matt stone-like surface finish.

1.75
2.85
Concrete
Granite
Pottery Clay
Terracotta
250
500
2000

If a product is out of stock, it is usually replenished within two weeks.

SKU: StoneFil Tags: , , , , ,

StoneFil is filled with 50% of powdered stone. This high stone-filling has resulted in a 3D printer filament with remarkable aesthetic features. StoneFil is an easy-to-print 3D printer filament and printed objects have an extremely matte stone-like finish. Due to its high content of stone powder, its density is higher than regular PLA’s.

StoneFil is a filament which is based on our modified and easy-to-print EasyFil PLA compound.

Unique features

  • Easy to print
  • 50% gravimetric powdered stone filling
  • ±37% heavier than “normal” PLA
  • Matte and rough stone-like finish

 

General printing guidelines *

Nozzle size: ≥ 0.4mm Layer height: ≥ 0.2mm Flow rate: ± 110%
Print temp: ± 215 – 230° C Print speed: Slow Retraction: Yes ± 5mm
Heat bed: ± 0 – 60° C Fan speed: 50-100% Experience level: Beginner

*) Above displayed settings are meant as guidance to find your optimal print settings. These ranges in settings should work for most printers, but please do feel free to experiment outside these ranges if you think it is suitable for your printer. There are a lot of different type of printers, hot-ends and printer offsets that it is extremely difficult to give an overall one-size-fits-all setting.

 

Abrasiveness

StoneFil has a very high filling with stone powders and therefore the filament can have a slightly more abrasive effect on brass nozzles than unfilled filaments.

Filament length

ρ: 1.70 g/cc 50 gr coil 0.5 Kg spool
Ø 1.75mm ± 12.2m ± 122m
Ø 2.85mm ± 4.6m ± 46m

 

Nozzle cleaning

When printing with filled/composite filaments it is recommended to clean your nozzle immediately after printing by feeding 15-20cm PLA filament through your nozzle. This will make sure that any potential fillers are flown out of your nozzle. It is even better to use glow in the dark PLA as the extremely hard phosphorous particles are much more likely to scrape out residual waste from your nozzle.

Product export information

HS Code: 39169090 Description: Monofilament Country of origin: the Netherlands

 

Compliance *

This filament is compliant to below listed directives and regulations.

  • RoHS directive 2011/65/EC
  • REACH directive 1907/2006/EC

*) This declaration of conformity to directives and regulations is prepared according to our present standard of knowledge and may be amended if new cognitions are available and applies only for the above described products.

Technical Datasheet:

Safety Datasheet: